Page 1 of 1

BHO

Posted: Fri 16th Feb 2018 10:16 pm
by macky
Have some friends buying oven ,vacuum pump :wink: Was doing a little reading ,figured some here may have suggestion e.g. buy all in one or pump oven separate? Suggestion on good extractor any help would be good . Have say 10,000 dollar budget….RO 420

Re: BHO

Posted: Sat 17th Feb 2018 06:48 pm
by macky
never mind went close loop from company in Detroit for 30,000 :mrgreen:

Re: BHO

Posted: Sat 17th Feb 2018 07:03 pm
by CopenhagenCouple
Jeez, someone's​ got cash to spend :D hope it makes some great dabables :D :mrgreen:

Re: BHO

Posted: Sat 17th Feb 2018 07:09 pm
by OneHighMofo
They weren't interested in Rosin Macky?
I just dropped £500 on a pneumatic 10 tonne bench press with heated plates and am squising out rosin at 20-25%.
Big difference in cost!

Closed loop is the only way to play though, for safefy and purity reasons there's just no alternative - very cool setup 8)

Re: BHO

Posted: Sat 17th Feb 2018 10:40 pm
by macky
CopenhagenCouple wrote:
Sat 17th Feb 2018 07:03 pm
Jeez, someone's​ got cash to spend :D hope it makes some great dabables :D :mrgreen:
I was in for share for oven ,pump to use in edibles ,Then as you said guys with deep pockets jumped in :D
Will know where to find clean dabbales any way.

Re: BHO

Posted: Sat 3rd Mar 2018 04:14 pm
by macky
So it seem,s the group project fell apart :D
So me and a buddy going it alone ,where leaning toward a company from here Ledab.ca
5lb extractors closed loop is for sure ,vac pump and oven will be decided after consolation with company at retail location.
Now who can tell me where to get articles on making HBO,s any advice would help.
Seem,s like we will have samples for a few in July :wink:

RO 420 :mrgreen:

Re: BHO

Posted: Mon 19th Mar 2018 02:48 pm
by RoMoney
OneHighMofo wrote:
Sat 17th Feb 2018 07:09 pm
I just dropped £500 on a pneumatic 10 tonne bench press with heated plates and am squising out rosin at 20-25%.
Nice, was looking at the RTP Manual Twist Press with a mate, obviously wouldn't get the same returns as with a pneumatic one though, but easier if you're in an apartment.

https://www.rosintechproducts.eu/produc ... nual-twist

Re: BHO

Posted: Mon 19th Mar 2018 04:06 pm
by OneHighMofo
RoMoney wrote:
Mon 19th Mar 2018 02:48 pm
obviously wouldn't get the same returns as with a pneumatic one though, but easier if you're in an apartment.

https://www.rosintechproducts.eu/produc ... nual-twist
Honestly dude I think you'll be surprised. I reckon that unit will be every bit as good.
I bought a standard 10 tonne bench press and some plates from Amazon and worked out pretty quickly that pressure rating is overkill. Haven't seen any further yield than what's available pressing at 5-6 tonnes on the guage.
Crack on - you won't be dissapointed; the biggest win so far (apart from being able to press up to 7g at a time)has been being able to press at lower temps than I could with hair straighteners preserving more taste.

Re: BHO

Posted: Mon 19th Mar 2018 06:17 pm
by RoMoney
OneHighMofo wrote:
Mon 19th Mar 2018 04:06 pm
RoMoney wrote:
Mon 19th Mar 2018 02:48 pm
obviously wouldn't get the same returns as with a pneumatic one though, but easier if you're in an apartment.

https://www.rosintechproducts.eu/produc ... nual-twist
Honestly dude I think you'll be surprised. I reckon that unit will be every bit as good.
I bought a standard 10 tonne bench press and some plates from Amazon and worked out pretty quickly that pressure rating is overkill. Haven't seen any further yield than what's available pressing at 5-6 tonnes on the guage.
Crack on - you won't be dissapointed; the biggest win so far (apart from being able to press up to 7g at a time)has been being able to press at lower temps than I could with hair straighteners preserving more taste.
Cool. encouraging to hear!

Re: BHO

Posted: Sun 12th Jan 2020 11:15 pm
by cantona7
so how did it go? you got the closed loop system , did you go with the vac oven or other method? if you get another CLS try open source steel out of seattle. usually some good deals.

Re: BHO

Posted: Wed 15th Jan 2020 11:13 am
by AudioKush
Saw the topic title and wanted to chime in. I've been involved in cannabis extractions since mid 2000s. I remember before "dabs" were a term. HMK Ti Vapor Curve was the og way to smoke. Then Vapor Swing copied the design and won at High Times w/ best new invention.

Re: BHO

Posted: Sat 18th Jan 2020 10:07 am
by cantona7
AudioKush wrote:
Wed 15th Jan 2020 11:13 am
Saw the topic title and wanted to chime in. I've been involved in cannabis extractions since mid 2000s. I remember before "dabs" were a term. HMK Ti Vapor Curve was the og way to smoke. Then Vapor Swing copied the design and won at High Times w/ best new invention.
i actually still have my hmk..and my old hitman domeless system which was the basis for the first domeless system. never use them though.

Re: BHO

Posted: Mon 9th Mar 2020 12:18 pm
by macky
cantona7 wrote:
Sun 12th Jan 2020 11:15 pm
so how did it go? you got the closed loop system , did you go with the vac oven or other method? if you get another CLS try open source steel out of seattle. usually some good deals.
Never got vacuum pump ,but bought close loop from la dab a company here from Quebec. One freind is making gummies another is tumbling weed and mixing with the oil to make hash .Selling disposible vape pens 1000 in box for 10,000dollars .
I prefer spreading on a paper with weed .starting to like gummies over canna butter baked goods . Dry weed prices are dropping fast even legal weed prices are going down. Everyone can grow 4 plants in or out door and you can get medical grow license with a little effort :mrgreen: . My self is grandfathered for life under a decision by a judge a few years back 37 indoor 10out door ......as CC said to me a few years back “That’s the most beautiful piece of paper I have every seen .....can I take a picture” :wink: